U.S. flag

An official website of the United States government

Dot gov

Official websites use .gov
A .gov website belongs to an official government organization in the United States.

Https

Secure .gov websites use HTTPS
A lock () or https:// means you’ve safely connected to the .gov website. Share sensitive information only on official, secure websites.

Breadcrumb

  1. Home

EM304 Water Column Sonar Data Collected During EX2506

Acoustic operations included Kongsberg EM 304 multibeam sonar, Simrad EK80 split-beam sonar, Knudsen 3260 sub-bottom profiler, and acoustic Doppler current profiler (ADCP) data collection to map the seafloor, sub-seafloor, and water column, as well as to provide operational information for CTD casts. Standard survey operations include concurrent collection of multibeam, split-beam, and sub-bottom sonar data synchronized using a Kongsberg Synchronization Unit (K-Sync) with the EM 304 set as the master. The ADCPs were secured during standard surveying operations due to interference with other sonars, but were used to collect data when entering and exiting port. During conductivity, temperature, and depth system (CTD) operations, the EM 304 multibeam sonar and Knudsen sub-bottom profiler were secured to allow the ADCPs and split-beam sonars to collect data.
Mapping operations were planned to maximize edge matching of existing data or to fill data gaps in areas with incomplete bathymetric coverage. In regions with no existing data, lines were optimized for potential discoveries and to complete relatively large continuous areas to support interpretation of features from bathymetry and backscatter. Targeted mapping operations were conducted within the Palau National Marine Sanctuary. Mapping operations occurred 24 hours/per day.

Okeanos Explorer is equipped with a 26 kHz Kongsberg EM 304 MKII multibeam sonar. The multibeam sonar was used to collect seafloor bathymetry, seafloor backscatter, and water column backscatter. Bathymetric and seafloor backscatter data are stored in .kmall files as beam-averaged backscatter values and as full time-series values (snippets) within each beam. Water column backscatter data are stored separately in .kmwcd files.
Throughout the expedition, mapping watchstanders monitored multibeam data quality in real time. Ship speed was adjusted to maintain data quality and sounding density as necessary, and line spacing was planned to ensure one-quarter to one-third swath-width overlap between lines, depending on the environmental conditions and impact on the quality of the outer swath regions. Maximum angles in the Seafloor Information System (SIS) were generally left open (65°/65°) during transit to maximize data collection and were adjusted on the port and starboard sides to ensure the best data quality and coverage. If outer beams were returning obviously spurious soundings (e.g., due to attenuation or low grazing angle), beam angles were gradually reduced and monitored closely until a high-quality swath was obtained.
Real-time surface sound speed values were provided by a Reson SV70 sound velocity probe mounted in close proximity to the EM 304 transducer and were monitored in SIS for deviations from the values determined by sound speed casts. Sound speed profiles were collected every six hours or more frequently as dictated by local oceanographic conditions (typically every two hours when operating in more dynamic areas).
Vessel positioning and attitude were measured by Applanix POS MV V5 and Kongsberg Seapath 380 positioning systems during data collection. This redundancy allows for either system to be the primary source of positioning/attitude for the multibeam data in the event that the other system fails. Positioning/attitude data were applied to the multibeam data in real time and were stored in .kmall files. The primary system used is noted in the processing logs.

Okeanos Explorer is equipped with a Knudsen 3260 sub-bottom profiler with a central frequency of 3.5 kHz. This sonar was used to collect echogram images of shallow geological layers underneath the seafloor to a maximum depth of approximately 80 m below the seafloor. Phase, range, and gain were monitored and optimized for data collection. New files were created when changes were made to pulse lengths and/or power settings.

Okeanos Explorer is equipped with a suite of five Simrad EK80 split-beam sonars: five wide-band transceivers (WBTs), the 18, 38, 70, 120, and 200 kHz sonars. These quantitative scientific echosounders were calibrated to identify the target strength of water column acoustic reflectors (e.g., deep scattering layers, fish, gas bubbles from seeps), providing additional information about water column characteristics and anomalies. The 200 kHz was not collected during this cruise due to a power issue post WBT install.
Calibrations were performed during EX2506, and these calibration values were most appropriate for the EX2506 dataset. The calibration files are archived with the sonar data, and the calibration report is available as a supplemental file to the 2025 mapping readiness report (Copeland et al. 2025).
The split-beam sonars were used continuously throughout EX2506 during mapping operations and CTD operations.

Okeanos Explorer is equipped with two acoustic Doppler current profilers (ADCPs), a Teledyne Workhorse Mariner (300 kHz) and a Teledyne Ocean Surveyor (38 kHz). Depending on environmental conditions, the 300 kHz system provides ocean current data to a depth of approximately 70 m, and the 38 kHz system provides data to a depth of approximately 1,200 m. Only the 300 kHz system was operable during this expedition. The ADCP was used to gather data prior to CTD deployments and EK80 calibration to assess currents in support of safe operations.

About this Dataset

Updated: 2026-11-17
Metadata Last Updated: 2026-11-04T08:49:41.615Z
Date Created: N/A
Data Provided by:
Dataset Owner: N/A

Access this data

Contact dataset owner Access URL
Table representation of structured data
Title EM304 Water Column Sonar Data Collected During EX2506
Description Acoustic operations included Kongsberg EM 304 multibeam sonar, Simrad EK80 split-beam sonar, Knudsen 3260 sub-bottom profiler, and acoustic Doppler current profiler (ADCP) data collection to map the seafloor, sub-seafloor, and water column, as well as to provide operational information for CTD casts. Standard survey operations include concurrent collection of multibeam, split-beam, and sub-bottom sonar data synchronized using a Kongsberg Synchronization Unit (K-Sync) with the EM 304 set as the master. The ADCPs were secured during standard surveying operations due to interference with other sonars, but were used to collect data when entering and exiting port. During conductivity, temperature, and depth system (CTD) operations, the EM 304 multibeam sonar and Knudsen sub-bottom profiler were secured to allow the ADCPs and split-beam sonars to collect data. Mapping operations were planned to maximize edge matching of existing data or to fill data gaps in areas with incomplete bathymetric coverage. In regions with no existing data, lines were optimized for potential discoveries and to complete relatively large continuous areas to support interpretation of features from bathymetry and backscatter. Targeted mapping operations were conducted within the Palau National Marine Sanctuary. Mapping operations occurred 24 hours/per day. Okeanos Explorer is equipped with a 26 kHz Kongsberg EM 304 MKII multibeam sonar. The multibeam sonar was used to collect seafloor bathymetry, seafloor backscatter, and water column backscatter. Bathymetric and seafloor backscatter data are stored in .kmall files as beam-averaged backscatter values and as full time-series values (snippets) within each beam. Water column backscatter data are stored separately in .kmwcd files. Throughout the expedition, mapping watchstanders monitored multibeam data quality in real time. Ship speed was adjusted to maintain data quality and sounding density as necessary, and line spacing was planned to ensure one-quarter to one-third swath-width overlap between lines, depending on the environmental conditions and impact on the quality of the outer swath regions. Maximum angles in the Seafloor Information System (SIS) were generally left open (65°/65°) during transit to maximize data collection and were adjusted on the port and starboard sides to ensure the best data quality and coverage. If outer beams were returning obviously spurious soundings (e.g., due to attenuation or low grazing angle), beam angles were gradually reduced and monitored closely until a high-quality swath was obtained. Real-time surface sound speed values were provided by a Reson SV70 sound velocity probe mounted in close proximity to the EM 304 transducer and were monitored in SIS for deviations from the values determined by sound speed casts. Sound speed profiles were collected every six hours or more frequently as dictated by local oceanographic conditions (typically every two hours when operating in more dynamic areas). Vessel positioning and attitude were measured by Applanix POS MV V5 and Kongsberg Seapath 380 positioning systems during data collection. This redundancy allows for either system to be the primary source of positioning/attitude for the multibeam data in the event that the other system fails. Positioning/attitude data were applied to the multibeam data in real time and were stored in .kmall files. The primary system used is noted in the processing logs. Okeanos Explorer is equipped with a Knudsen 3260 sub-bottom profiler with a central frequency of 3.5 kHz. This sonar was used to collect echogram images of shallow geological layers underneath the seafloor to a maximum depth of approximately 80 m below the seafloor. Phase, range, and gain were monitored and optimized for data collection. New files were created when changes were made to pulse lengths and/or power settings. Okeanos Explorer is equipped with a suite of five Simrad EK80 split-beam sonars: five wide-band transceivers (WBTs), the 18, 38, 70, 120, and 200 kHz sonars. These quantitative scientific echosounders were calibrated to identify the target strength of water column acoustic reflectors (e.g., deep scattering layers, fish, gas bubbles from seeps), providing additional information about water column characteristics and anomalies. The 200 kHz was not collected during this cruise due to a power issue post WBT install. Calibrations were performed during EX2506, and these calibration values were most appropriate for the EX2506 dataset. The calibration files are archived with the sonar data, and the calibration report is available as a supplemental file to the 2025 mapping readiness report (Copeland et al. 2025). The split-beam sonars were used continuously throughout EX2506 during mapping operations and CTD operations. Okeanos Explorer is equipped with two acoustic Doppler current profilers (ADCPs), a Teledyne Workhorse Mariner (300 kHz) and a Teledyne Ocean Surveyor (38 kHz). Depending on environmental conditions, the 300 kHz system provides ocean current data to a depth of approximately 70 m, and the 38 kHz system provides data to a depth of approximately 1,200 m. Only the 300 kHz system was operable during this expedition. The ADCP was used to gather data prior to CTD deployments and EK80 calibration to assess currents in support of safe operations.
Modified 2026-11-04T08:49:41.615Z
Publisher Name N/A
Contact N/A
Keywords Earth Science > Oceans > Ocean Acoustics > Acoustic Scattering , Earth Science > Oceans > Aquatic Sciences > Fisheries , Earth Science > Oceans > Ocean Acoustics , Earth Science > Biosphere > Ecosystems > Marine Ecosystems > Pelagic , Earth Science > Biosphere > Ecosystems > Marine Ecosystems , Earth Science > Biosphere > Ecosystems > Marine Ecosystems > Benthic , Earth Science > Biosphere > Ecosystems > Aquatic Ecosystems , Earth Science > Oceans > Bathymetry/Seafloor Topography > Bathymetry , Earth Science > Oceans > Bathymetry/Seafloor Topography > Seafloor Topography , North Pacific Ocean , DOC/NOAA/NESDIS/NCEI > National Centers for Environmental Information, NESDIS, NOAA, U.S. Department of Commerce , DOC/NOAA/NESDIS/NGDC > National Geophysical Data Center, NESDIS, NOAA, U.S. Department of Commerce , Vertical Location > Water Column , In Situ/Laboratory Instruments > Profilers/Sounders > Acoustic Sounders > WCMS > Water Column Mapping System , oceans , geoscientificInformation
{
    "identifier": "gov.noaa.ncei:EX2506_EM304",
    "accessLevel": "public",
    "contactPoint": {
        "@type": "vcard:Contact",
        "fn": "Your contact point",
        "hasEmail": "mailto:[email protected]"
    },
    "programCode": [
        "010:000"
    ],
    "landingPage": "",
    "title": "EM304 Water Column Sonar Data Collected During EX2506",
    "description": "Acoustic operations included Kongsberg EM 304 multibeam sonar, Simrad EK80 split-beam sonar, Knudsen 3260 sub-bottom profiler, and acoustic Doppler current profiler (ADCP) data collection to map the seafloor, sub-seafloor, and water column, as well as to provide operational information for CTD casts. Standard survey operations include concurrent collection of multibeam, split-beam, and sub-bottom sonar data synchronized using a Kongsberg Synchronization Unit (K-Sync) with the EM 304 set as the master. The ADCPs were secured during standard surveying operations due to interference with other sonars, but were used to collect data when entering and exiting port. During conductivity, temperature, and depth system (CTD) operations, the EM 304 multibeam sonar and Knudsen sub-bottom profiler were secured to allow the ADCPs and split-beam sonars to collect data.\nMapping operations were planned to maximize edge matching of existing data or to fill data gaps in areas with incomplete bathymetric coverage. In regions with no existing data, lines were optimized for potential discoveries and to complete relatively large continuous areas to support interpretation of features from bathymetry and backscatter. Targeted mapping operations were conducted within the Palau National Marine Sanctuary. Mapping operations occurred 24 hours\/per day.\n\nOkeanos Explorer is equipped with a 26 kHz Kongsberg EM 304 MKII multibeam sonar. The multibeam sonar was used to collect seafloor bathymetry, seafloor backscatter, and water column backscatter. Bathymetric and seafloor backscatter data are stored in .kmall files as beam-averaged backscatter values and as full time-series values (snippets) within each beam. Water column backscatter data are stored separately in .kmwcd files.\nThroughout the expedition, mapping watchstanders monitored multibeam data quality in real time. Ship speed was adjusted to maintain data quality and sounding density as necessary, and line spacing was planned to ensure one-quarter to one-third swath-width overlap between lines, depending on the environmental conditions and impact on the quality of the outer swath regions. Maximum angles in the Seafloor Information System (SIS) were generally left open (65\u00b0\/65\u00b0) during transit to maximize data collection and were adjusted on the port and starboard sides to ensure the best data quality and coverage. If outer beams were returning obviously spurious soundings (e.g., due to attenuation or low grazing angle), beam angles were gradually reduced and monitored closely until a high-quality swath was obtained.\nReal-time surface sound speed values were provided by a Reson SV70 sound velocity probe mounted in close proximity to the EM 304 transducer and were monitored in SIS for deviations from the values determined by sound speed casts. Sound speed profiles were collected every six hours or more frequently as dictated by local oceanographic conditions (typically every two hours when operating in more dynamic areas). \nVessel positioning and attitude were measured by Applanix POS MV V5 and Kongsberg Seapath 380 positioning systems during data collection. This redundancy allows for either system to be the primary source of positioning\/attitude for the multibeam data in the event that the other system fails. Positioning\/attitude data were applied to the multibeam data in real time and were stored in .kmall files. The primary system used is noted in the processing logs.\n\nOkeanos Explorer is equipped with a Knudsen 3260 sub-bottom profiler with a central frequency of 3.5 kHz. This sonar was used to collect echogram images of shallow geological layers underneath the seafloor to a maximum depth of approximately 80 m below the seafloor. Phase, range, and gain were monitored and optimized for data collection. New files were created when changes were made to pulse lengths and\/or power settings.\n\nOkeanos Explorer is equipped with a suite of five Simrad EK80 split-beam sonars: five wide-band transceivers (WBTs), the 18, 38, 70, 120, and 200 kHz sonars. These quantitative scientific echosounders were calibrated to identify the target strength of water column acoustic reflectors (e.g., deep scattering layers, fish, gas bubbles from seeps), providing additional information about water column characteristics and anomalies. The 200 kHz was not collected during this cruise due to a power issue post WBT install. \nCalibrations were performed during EX2506, and these calibration values were most appropriate for the EX2506 dataset. The calibration files are archived with the sonar data, and the calibration report is available as a supplemental file to the 2025 mapping readiness report (Copeland et al. 2025). \nThe split-beam sonars were used continuously throughout EX2506 during mapping operations and CTD operations.\n\nOkeanos Explorer is equipped with two acoustic Doppler current profilers (ADCPs), a Teledyne Workhorse Mariner (300 kHz) and a Teledyne Ocean Surveyor (38 kHz). Depending on environmental conditions, the 300 kHz system provides ocean current data to a depth of approximately 70 m, and the 38 kHz system provides data to a depth of approximately 1,200 m. Only the 300 kHz system was operable during this expedition. The ADCP was used to gather data prior to CTD deployments and EK80 calibration to assess currents in support of safe operations.",
    "language": "",
    "distribution": [
        {
            "@type": "dcat:Distribution",
            "mediaType": "application\/json",
            "accessURL": "https:\/\/www.ncei.noaa.gov\/metadata\/geoportal\/\/rest\/metadata\/item\/gov.noaa.ncei%3AEX2506_EM304"
        },
        {
            "@type": "dcat:Distribution",
            "mediaType": "text\/html",
            "accessURL": "https:\/\/www.ncei.noaa.gov\/metadata\/geoportal\/\/rest\/metadata\/item\/gov.noaa.ncei%3AEX2506_EM304\/html"
        },
        {
            "@type": "dcat:Distribution",
            "mediaType": "application\/xml",
            "accessURL": "https:\/\/www.ncei.noaa.gov\/metadata\/geoportal\/\/rest\/metadata\/item\/gov.noaa.ncei%3AEX2506_EM304\/xml"
        }
    ],
    "bureauCode": [
        "010:04"
    ],
    "modified": "2026-11-04T08:49:41.615Z",
    "publisher": {
        "@type": "org:Organization",
        "name": "Your Publisher"
    },
    "theme": "",
    "keyword": [
        "Earth Science > Oceans > Ocean Acoustics > Acoustic Scattering",
        "Earth Science > Oceans > Aquatic Sciences > Fisheries",
        "Earth Science > Oceans > Ocean Acoustics",
        "Earth Science > Biosphere > Ecosystems > Marine Ecosystems > Pelagic",
        "Earth Science > Biosphere > Ecosystems > Marine Ecosystems",
        "Earth Science > Biosphere > Ecosystems > Marine Ecosystems > Benthic",
        "Earth Science > Biosphere > Ecosystems > Aquatic Ecosystems",
        "Earth Science > Oceans > Bathymetry\/Seafloor Topography > Bathymetry",
        "Earth Science > Oceans > Bathymetry\/Seafloor Topography > Seafloor Topography",
        "North Pacific Ocean",
        "DOC\/NOAA\/NESDIS\/NCEI > National Centers for Environmental Information, NESDIS, NOAA, U.S. Department of Commerce",
        "DOC\/NOAA\/NESDIS\/NGDC > National Geophysical Data Center, NESDIS, NOAA, U.S. Department of Commerce",
        "Vertical Location > Water Column",
        "In Situ\/Laboratory Instruments > Profilers\/Sounders > Acoustic Sounders > WCMS > Water Column Mapping System",
        "oceans",
        "geoscientificInformation"
    ]
}